View MC78L05ACP_281726.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MC78L00A Series Three-Terminal Low Current Positive Voltage Regulators
The MC78L00A Series of positive voltage regulators are inexpensive, easy-to-use devices suitable for a multitude of applications that require a regulated supply of up to 100 mA. Like their higher powered MC7800 and MC78M00 Series cousins, these regulators feature internal current limiting and thermal shutdown making them remarkably rugged. No external components are required with the MC78L00 devices in many applications. These devices offer a substantial performance advantage over the traditional zener diode-resistor combination, as output impedance and quiescent current are substantially reduced. * Wide Range of Available, Fixed Output Voltages * Low Cost * Internal Short Circuit Current Limiting * Internal Thermal Overload Protection * No External Components Required * Complementary Negative Regulators Offered (MC79L00A Series)
Input Q12 Q10 Q4 Q6 5.0k 3.0 0-25k 19k C Z1 420 Q2 Q7 1.0k Ground Q8 2.2k Q9 2.85k Output *SOP-8 is an internally modified SO-8 package. Pins 2, 3, 6, and 7 are electrically common to the die attach flag. This internal lead frame modification decreases package thermal resistance and increases power dissipation capability when appropriately mounted on a printed circuit board. SOP-8 conforms to all external dimensions of the standard SO-8 package.
http://onsemi.com
1
TO-92 P SUFFIX CASE 029 2 3 Pin: 1. Output 2. Ground 3. Input
8 1
SOP-8* D SUFFIX CASE 751
15k Q1 3.8k
Q3
Q5
Q11
1.2k
1.9k
PIN CONNECTIONS
VOUT 1 GND 2 GND 3 NC 4 (Top View) 8 7 6 5 VIN GND GND NC
Figure 1. Representative Schematic Diagram
Input Cin* 0.33F MC78LXXA Output CO**
ORDERING INFORMATION
See detailed ordering and shipping information in the package dimensions section on page 8 of this data sheet.
DEVICE MARKING INFORMATION
See general marking information in the device marking section on page 10 of this data sheet.
Figure 2. Standard Application
A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0 V above the output voltage even during the low point on the input ripple voltage. * Cin is required if regulator is located an appreciable distance from power supply filter. ** CO is not needed for stability; however, it does improve transient response.
(c) Semiconductor Components Industries, LLC, 2001
1
October, 2001 - Rev. 2
Publication Order Number: MC78L00A/D
MC78L00A Series
MAXIMUM RATINGS (TA = +125C, unless otherwise noted.)
Rating Input Voltage (2.6 V-8.0 V) Input Voltage (12 V-18 V) Input Voltage (24 V) Storage Temperature Range Operating Junction Temperature Range Symbol VI Value 30 35 40 -65 to +150 0 to +150 Unit Vdc
Tstg TJ
C C
ELECTRICAL CHARACTERISTICS (VI = 10 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, -40C < TJ < +125C (for MC78LXXAB), 0C < TJ < +125C (for MC78LXXAC), unless otherwise noted.)
MC78L05AC, AB Characteristics Output Voltage (TJ = +25C) Line Regulation (TJ = +25C, IO = 40 mA) 7.0 Vdc VI 20 Vdc 8.0 Vdc VI 20 Vdc Load Regulation (TJ = +25C, 1.0 mA IO 100 mA) (TJ = +25C, 1.0 mA IO 40 mA) Output Voltage (7.0 Vdc VI 20 Vdc, 1.0 mA IO 40 mA) (VI = 10 V, 1.0 mA IO 70 mA) Input Bias Current (TJ = +25C) (TJ = +125C) Input Bias Current Change (8.0 Vdc VI 20 Vdc) (1.0 mA IO 40 mA) Output Noise Voltage (TA = +25C, 10 Hz f 100 kHz) Ripple Rejection (IO = 40 mA, f = 120 Hz, 8.0 Vdc VI 18 V, TJ = +25C) Dropout Voltage (TJ = +25C) Symbol VO Regline - - Regload - - VO 4.75 4.75 IIB - - IIB - - Vn RR VI - VO - 41 - - - 40 49 1.7 1.5 0.1 - - - V dB Vdc 3.8 - 6.0 5.5 mA - - 5.25 5.25 mA 11 5.0 60 30 Vdc 55 45 150 100 mV Min 4.8 Typ 5.0 Max 5.2 Unit Vdc mV
http://onsemi.com
2
MC78L00A Series
ELECTRICAL CHARACTERISTICS (VI = 14 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, -40C < TJ < +125C (for MC78LXXAB), 0C < TJ < +125C (for MC78LXXAC), unless otherwise noted.)
MC78L08AC, AB Characteristics Output Voltage (TJ = +25C) Line Regulation (TJ = +25C, IO = 40 mA) 10.5 Vdc VI 23 Vdc 11 Vdc VI 23 Vdc Load Regulation (TJ = +25C, 1.0 mA IO 100 mA) (TJ = +25C, 1.0 mA IO 40 mA) Output Voltage (10.5 Vdc VI 23 Vdc, 1.0 mA IO 40 mA) (VI = 14 V, 1.0 mA IO 70 mA) Input Bias Current (TJ = +25C) (TJ = +125C) Input Bias Current Change (11 Vdc VI 23 Vdc) (1.0 mA IO 40 mA) Output Noise Voltage (TA = +25C, 10 Hz f 100 kHz) Ripple Rejection (IO = 40 mA, f = 120 Hz, 12 V VI 23 V, TJ = +25C) Dropout Voltage (TJ = +25C) Symbol VO Regline - - Regload - - VO 7.6 7.6 IIB - - IIB - - Vn RR VI - VO - 37 - - - 60 57 1.7 1.5 0.1 - - - V dB Vdc 3.0 - 6.0 5.5 mA - - 8.4 8.4 mA 15 8.0 80 40 Vdc 20 12 175 125 mV Min 7.7 Typ 8.0 Max 8.3 Unit Vdc mV
ELECTRICAL CHARACTERISTICS (VI = 15 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, -40C < TJ < +125C (for MC78LXXAB), 0C < TJ < +125C (for MC78LXXAC), unless otherwise noted.)
MC78L09AC, AB Characteristics Output Voltage (TJ = +25C) Line Regulation (TJ = +25C, IO = 40 mA) 11.5 Vdc VI 24 Vdc 12 Vdc VI 24 Vdc Load Regulation (TJ = +25C, 1.0 mA IO 100 mA) (TJ = +25C, 1.0 mA IO 40 mA) Output Voltage (11.5 Vdc VI 24 Vdc, 1.0 mA IO 40 mA) (VI = 15 V, 1.0 mA IO 70 mA) Input Bias Current (TJ = +25C) (TJ = +125C) Input Bias Current Change (11 Vdc VI 23 Vdc) (1.0 mA IO 40 mA) Output Noise Voltage (TA = +25C, 10 Hz f 100 kHz) Ripple Rejection (IO = 40 mA, f = 120 Hz, 13 V VI 24 V, TJ = +25C) Dropout Voltage (TJ = +25C) Symbol VO Regline - - Regload - - VO 8.5 8.5 IIB - - IIB - - Vn RR VI - VO - 37 - - - 60 57 1.7 1.5 0.1 - - - V dB Vdc 3.0 - 6.0 5.5 mA - - 9.5 9.5 mA 15 8.0 90 40 Vdc 20 12 175 125 mV Min 8.6 Typ 9.0 Max 9.4 Unit Vdc mV
http://onsemi.com
3
MC78L00A Series
ELECTRICAL CHARACTERISTICS (VI = 19 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, -40C < TJ < +125C (for MC78LXXAB), 0C < TJ < +125C (for MC78LXXAC), unless otherwise noted.)
MC78L12AC, AB Characteristics Output Voltage (TJ = +25C) Line Regulation (TJ = +25C, IO = 40 mA) 14.5 Vdc VI 27 Vdc 16 Vdc VI 27 Vdc Load Regulation (TJ = +25C, 1.0 mA IO 100 mA) (TJ = +25C, 1.0 mA IO 40 mA) Output Voltage (14.5 Vdc VI 27 Vdc, 1.0 mA IO 40 mA) (VI = 19 V, 1.0 mA IO 70 mA) Input Bias Current (TJ = +25C) (TJ = +125C) Input Bias Current Change (16 Vdc VI 27 Vdc) (1.0 mA IO 40 mA) Output Noise Voltage (TA = +25C, 10 Hz f 100 kHz) Ripple Rejection (IO = 40 mA, f = 120 Hz, 15 V VI 25 V, TJ = +25C) Dropout Voltage (TJ = +25C) Symbol VO Regline - - Regload - - VO 11.4 11.4 IIB - - IIB - - Vn RR VI - VO - 37 - - - 80 42 1.7 1.5 0.1 - - - V dB Vdc 4.2 - 6.5 6.0 mA - - 12.6 12.6 mA 20 10 100 50 Vdc 120 100 250 200 mV Min 11.5 Typ 12 Max 12.5 Unit Vdc mV
ELECTRICAL CHARACTERISTICS (VI = 23 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, -40C < TJ < +125C (for MC78LXXAB), S 0C < TJ < +125C (for MC78LXXAC), unless otherwise noted.)
MC78L15AC, AB Characteristics Output Voltage (TJ = +25C) Line Regulation (TJ = +25C, IO = 40 mA) 17.5 Vdc VI 30 Vdc 20 Vdc VI 30 Vdc Load Regulation (TJ = +25C, 1.0 mA IO 100 mA) (TJ = +25C, 1.0 mA IO 40 mA) Output Voltage (17.5 Vdc VI 30 Vdc, 1.0 mA IO 40 mA) (VI = 23 V, 1.0 mA IO 70 mA) Input Bias Current (TJ = +25C) (TJ = +125C) Input Bias Current Change (20 Vdc VI 30 Vdc) (1.0 mA IO 40 mA) Output Noise Voltage (TA = +25C, 10 Hz f 100 kHz) Ripple Rejection (IO = 40 mA, f = 120 Hz, 18.5 V VI 28.5 V, TJ = +25C) Dropout Voltage (TJ = +25C) Symbol VO Regline - - Regload - - VO 14.25 14.25 IIB - - IIB - - Vn RR VI - VO - 34 - - - 90 39 1.7 1.5 0.1 - - - V dB Vdc 4.4 - 6.5 6.0 mA - - 15.75 15.75 mA 25 12 150 75 Vdc 130 110 300 250 mV Min 14.4 Typ 15 Max 15.6 Unit Vdc mV
http://onsemi.com
4
MC78L00A Series
ELECTRICAL CHARACTERISTICS (VI = 27 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, 0C < TJ < +125C, unless otherwise noted.)
MC78L18AC Characteristics Output Voltage (TJ = +25C) Line Regulation (TJ = +25C, IO = 40 mA) 21.4 Vdc VI 33 Vdc 20.7 Vdc VI 33 Vdc 22 Vdc VI 33 Vdc 21 Vdc VI 33 Vdc Load Regulation (TJ = +25C, 1.0 mA IO 100 mA) (TJ = +25C, 1.0 mA IO 40 mA) Output Voltage (21.4 Vdc VI 33 Vdc, 1.0 mA IO 40 mA) (20.7 Vdc VI 33 Vdc, 1.0 mA IO 40 mA) (VI = 27 V, 1.0 mA IO 70 mA) (VI = 27 V, 1.0 mA IO 70 mA) Input Bias Current (TJ = +25C) (TJ = +125C) Input Bias Current Change (22 Vdc VI 33 Vdc) (21 Vdc VI 33 Vdc) (1.0 mA IO 40 mA) Output Noise Voltage (TA = +25C, 10 Hz f 100 kHz) Ripple Rejection (IO = 40 mA, f = 120 Hz, 23 V VI 33 V, TJ = +25C) Dropout Voltage (TJ = +25C) Symbol VO Min 17.3 Typ 18 Max 18.7 Unit Vdc
Regline
- -
45 35 30 15
325 275
mV
Regload - - VO 17.1 17.1 IIB - - IIB - - Vn RR VI - VO - 33 - - - 150 48 1.7 1.5 0.1 - - - 3.1 - 6.5 6.0 - - 18.9 18.9 170 85
mV
Vdc
mA
mA
V dB Vdc
ELECTRICAL CHARACTERISTICS (VI = 33 V, IO = 40 mA, CI = 0.33 F, CO = 0.1 F, 0C < TJ < +125C, unless otherwise noted.)
MC78L24AC Characteristics Output Voltage (TJ = +25C) Line Regulation (TJ = +25C, IO = 40 mA) 27.5 Vdc VI 38 Vdc 28 Vdc VI 80 Vdc 27 Vdc VI 38 Vdc Load Regulation (TJ = +25C, 1.0 mA IO 100 mA) (TJ = +25C, 1.0 mA IO 40 mA) Output Voltage (28 Vdc VI 38 Vdc, 1.0 mA IO 40 mA) (27 Vdc VI 38 Vdc, 1.0 mA IO 40 mA) (28 Vdc VI = 33 Vdc, 1.0 mA IO 70 mA) (27 Vdc VI 33 Vdc, 1.0 mA IO 70 mA) Input Bias Current (TJ = +25C) (TJ = +125C) Input Bias Current Change (28 Vdc VI 38 Vdc) (1.0 mA IO 40 mA) Output Noise Voltage (TA = +25C, 10 Hz f 100 kHz) Ripple Rejection (IO = 40 mA, f = 120 Hz, 29 V VI 35 V, TJ = +25C) Dropout Voltage (TJ = +25C) Symbol VO Regline - - - Regload - - VO 22.8 22.8 IIB - - IIB - - Vn RR VI - VO - 31 - - - 200 45 1.7 1.5 0.1 - - - V dB Vdc 3.1 - 6.5 6.0 mA - - 25.2 25.2 mA 40 20 200 100 Vdc - 50 60 - 300 350 mV Min 23 Typ 24 Max 25 Unit Vdc mV
http://onsemi.com
5
MC78L00A Series
V I -V O , INPUT/OUTPUT DIFFERENTIAL VOLTAGE (V) 8.0 VO, OUTPUT VOLTAGE (V) MC78L05AC Vout = 5.0 V TJ = 25C IO = 1.0 mA 2.5 2.0 1.5 1.0 0.5 0 IO = 40 mA Dropout of Regulation is defined as when VO = 2% of VO 0 25 50 75 100 TJ, JUNCTION TEMPERATURE (C) 125 IO = 70 mA
6.0
4.0
2.0
IO = 40 mA
IO = 100 mA
IO = 1.0 mA
0
0
2.0
4.0 6.0 VI, INPUT VOLTAGE (V)
8.0
10
Figure 1. Dropout Characteristics
Figure 2. Dropout Voltage versus Junction Temperature
4.2 I IB , INPUT BIAS CURRENT (mA) 4.0 3.8 3.6 3.4 3.2 3.0 0 0 MC78L05AC VI = 10 V VO= 5.0 V IO = 40 mA 25 50 75 100 TA, AMBIENT TEMPERATURE (C) 125 I IB , INPUT BIAS CURRENT (mA)
5.0 4.0 3.0 2.0 1.0 0 MC78L05AC Vout = 5.0 V IO = 40 mA TJ = 25C
0
5.0
10
15 20 25 VI, INPUT VOLTAGE (V)
30
35
40
Figure 3. Input Bias Current versus Ambient Temperature
Figure 4. Input Bias Current versus Input Voltage
R JA, THERMAL RESISTANCE JUNCTION TO AIR ( C/W)
PD , POWER DISSIPATION (mW)
150 130
PD(max) for TA = 50C
2.8 2.4
1000
No Heatsink
90 70 50 30 0 10 RJA 20
100 RJA = 200C/W PD(max) to 25C = 625 mW 10 25 50 75 100 125 TA, AMBIENT TEMPERATURE (C) 150
L, LENGTH OF COPPER (mm)
Figure 5. Maximum Average Power Dissipation versus Ambient Temperature - TO-92 Type Package
Figure 6. SOP-8 Thermal Resistance and Maximum Power Dissipation versus P.C.B. Copper Length
http://onsemi.com
6
III I II IIIIIII I III IIIIIII
L 2.0 oz. Copper L 3.0 mm 30 40
110
Graph represents symmetrical layout
2.0 1.6 1.2 0.8 0.4 50
PD, MAXIMUM POWER DISSIPATION (W)
10,000
170
3.2
MC78L00A Series
APPLICATIONS INFORMATION
Design Considerations
The MC78L00A Series of fixed voltage regulators are designed with Thermal Overload Protection that shuts down the circuit when subjected to an excessive power overload condition. Internal Short Circuit Protection limits the maximum current the circuit will pass. In many low current applications, compensation capacitors are not required. However, it is recommended that the regulator input be bypassed with a capacitor if the regulator is connected to the power supply filter with long wire lengths, or if the output load capacitance is large. The
input bypass capacitor should be selected to provide good high-frequency characteristics to insure stable operation under all load conditions. A 0.33 F or larger tantalum, mylar, or other capacitor having low internal impedance at high frequencies should be chosen. The bypass capacitor should be mounted with the shortest possible leads directly across the regulators input terminals. Good construction techniques should be used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. Bypassing the output is also recommended.
+20V 0.33F Input 0.33F IO MC78L05A R Constant Current to Grounded Load
MC78L15A 2 MC1741 3 + 4 6.5 MPS U55 MPS A70 7
+VO 10k
6
0.33F 20V
10k -VO
The MC78L00 regulators can also be used as a current source when connected as above. In order to minimize dissipation the MC78L05C is chosen in this application. Resistor R determines the current as follows: 5.0 V IO = + IB R IIB = 3.8 mA over line and load changes For example, a 100 mA current source would require R to be a 50 , 1/2 W resistor and the output voltage compliance would be the input voltage less 7 V.
Figure 8. 15 V Tracking Voltage Regulator
+VI 0.33F -VI 0.33F MC79LXXA 0.1F -VO MC78LXXA 0.1F +VO
Figure 7. Current Regulator
Figure 9. Positive and Negative Regulator
http://onsemi.com
7
MC78L00A Series
ORDERING INFORMATION
Device MC78L05ABD MC78L05ABDR2 MC78L05ABP MC78L05ABPRA MC78L05ABPRE MC78L05ABPRM MC78L05ACD MC78L05ACDR2 MC78L05ACP MC78L05ACPRA MC78L05ACPRE MC78L05ACPRM MC78L05ACPRP MC78L08ABD MC78L08ABDR2 MC78L08ABP MC78L08ABPRA MC78L08ABPRP MC78L08ACD MC78L08ACDR2 MC78L08ACP MC78L08ACPRA MC78L08ACPRE MC78L08ACPRP MC78L09ABD MC78L09ABDR2 MC78L09ABPRA MC78L09ABPRP MC78L09ACD MC78L09ACDR2 MC78L09ACP TJ = 0 to +125C 9.0 V TJ = -40 to +125C 40 TJ = 0 to +125C 8.0 V TJ = -40 to +125C TJ = 0 to +125C 5.0 V TJ = -40 to +125C 40 Output Voltage Operating Temperature Range Package SOP-8 SOP-8 TO-92 TO-92 TO-92 TO-92 SOP-8 SOP-8 TO-92 TO-92 TO-92 TO-92 TO-92 SOP-8 SOP-8 TO-92 TO-92 TO-92 SOP-8 SOP-8 TO-92 TO-92 TO-92 TO-92 SOP-8 SOP-8 TO-92 TO-92 SOP-8 SOP-8 TO-92 Shipping 98 Units/Rail 2500 Tape & Reel 2000 Units/Bag 2000 Tape & Reel 2000 Units/Bag 2000 Ammo Pack 98 Units/Rail 2500 Tape & Reel 2000 Units/Bag 2000 Tape & Reel 2000 Tape & Reel 2000 Ammo Pack 2000 Ammo Pack 98 Units/Rail 2500 Tape & Reel 2000 Units/Bag 2000 Tape & Reel 2000 Units/Bag 98 Units/Rail 2500 Tape & Reel 2000 Units/Bag 2000 Tape & Reel 2000 Tape & Reel 2000 Ammo Pack 98 Units/Rail 2500 Tape & Reel 2000 Units/Bag 2000 Units/Bag 98 Units/Rail 2500 Tape & Reel 2000 Units/Bag
http://onsemi.com
8
MC78L00A Series
ORDERING INFORMATION (continued)
Device MC78L12ABD MC78L12ABDR2 MC78L12ABP MC78L12ABPRP MC78L12ACD MC78L12ACDR2 MC78L12ACP MC78L12ACPRA MC78L12ACPRE MC78L12ACPRM MC78L12ACPRP MC78L15ABD MC78L15ABDR2 MC78L15ABP MC78L15ABPRA MC78L15ABPRP MC78L15ACD MC78L15ACDR2 MC78L15ACP MC78L15ACPRA MC78L15ACPRP MC78L18ABP MC78L18ACP MC78L18ACPRA MC78L18ACPRM MC78L18ACPRP MC78L24ABP MC78L24ACP MC78L24ACPRA MC78L24ACPRP 24 V TJ = 0 to +125C TJ = -40 to +125C 18 V TJ = 0 to +125C TJ = -40 to +125C TJ = 0 to +125C 15 V TJ = -40 to +125C TJ = 0 to +125C 12 V TJ = -40 to +125C 40 Output Voltage Operating Temperature Range Package SOP-8 SOP-8 TO-92 TO-92 SOP-8 SOP-8 TO-92 TO-92 TO-92 TO-92 TO-92 SOP-8 SOP-8 TO-92 TO-92 TO-92 SOP-8 SOP-8 TO-92 TO-92 TO-92 TO-92 TO-92 TO-92 TO-92 TO-92 TO-92 TO-92 TO-92 TO-92 Shipping 98 Units/Rail 2500 Tape & Reel 2000 Units/Bag 2000 Units/Bag 98 Units/Rail 2500 Tape & Reel 2000 Units/Bag 2000 Tape & Reel 2000 Tape & Reel 2000 Ammo Pack 2000 Ammo Pack 98 Units/Rail 2500 Tape & Reel 2000 Units/Bag 2000 Tape & Reel 2000 Units/Bag 98 Units/Rail 2500 Tape & Reel 2000 Units/Bag 2000 Tape & Reel 2000 Ammo Pack 2000 Units/Bag 2000 Units/Bag 2000 Tape & Reel 2000 Units/Bag 2000 Ammo Pack 2000 Units/Bag 2000 Units/Bag 2000 Tape & Reel 2000 Ammo Pack
http://onsemi.com
9
MC78L00A Series
MARKING DIAGRAMS
SOP-8 D SUFFIX CASE 751 8 8LxxA ALYWB 1 xx A L Y W B, C 1 = 05, 08, 09, 12, or 15 = Assembly Location = Wafer Lot = Year = Work Week = Temperature Range 8 8LxxA ALYWC
TO-92 P SUFFIX CASE 029 MC78L zzABP ALYWW MC78L zzACP ALYWW
1 23 zz A L Y WW
123
= 05, 08, 09, 12, 15, 18 or 24 = Assembly Location = Wafer Lot = Year = Work Week
http://onsemi.com
10
MC78L00A Series
PACKAGE DIMENSIONS
TO-92 P SUFFIX CASE 29-11 ISSUE AL
A R P L
SEATING PLANE
B
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. INCHES MIN MAX 0.175 0.205 0.170 0.210 0.125 0.165 0.016 0.021 0.045 0.055 0.095 0.105 0.015 0.020 0.500 --0.250 --0.080 0.105 --0.100 0.115 --0.135 --MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.407 0.533 1.15 1.39 2.42 2.66 0.39 0.50 12.70 --6.35 --2.04 2.66 --2.54 2.93 --3.43 ---
K
XX G H V
1
D J C SECTION X-X N N
DIM A B C D G H J K L N P R V
SOP-8 D SUFFIX CASE 751-07 ISSUE W
-X- A
8 5
B
1 4
S
0.25 (0.010)
M
Y
M
-Y- G C -Z- H D 0.25 (0.010)
M SEATING PLANE
K
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A B C D G H J K M N S MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.33 0.51 1.27 BSC 0.10 0.25 0.19 0.25 0.40 1.27 0_ 8_ 0.25 0.50 5.80 6.20 INCHES MIN MAX 0.189 0.197 0.150 0.157 0.053 0.069 0.013 0.020 0.050 BSC 0.004 0.010 0.007 0.010 0.016 0.050 0_ 8_ 0.010 0.020 0.228 0.244
N
X 45 _
0.10 (0.004)
M
J
ZY
S
X
S
http://onsemi.com
11
MC78L00A Series
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer.
PUBLICATION ORDERING INFORMATION
Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: ONlit@hibbertco.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada JAPAN: ON Semiconductor, Japan Customer Focus Center 4-32-1 Nishi-Gotanda, Shinagawa-ku, Tokyo, Japan 141-0031 Phone: 81-3-5740-2700 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative.
http://onsemi.com
12
MC78L00A/D

▲Up To Search▲

Price & Availability of MC78L05ACP

	To Download MC78L05ACP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .